2 3 4 inch small diesel engine water pump

NegotiableUpdate on 02/26

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

2, 3, 4 inch small diesel engine water pump Hansi water pump set: It has fast power start, smooth operation, low vibration, low fuel consumption, small size, compact structure, stable and reliable ignition. The self-priming pump (also known as the clean water self-priming centrifugal pump) is one of the energy-saving self-priming pump series products developed by optimizing and improving similar self-priming pumps abroad. This pump belongs to the self-priming centrifugal pump, which has the advantages of compact structure, easy operation, stable operation, easy maintenance, high efficiency, long service life, and strong self-priming ability.

Product Details

2 3 4 inch small diesel engine water pump

Project Model Model Model			HS40DPE
Pump water pump	Suction prot diameter inlet diameter	mm	100 (4 ")
	Discharge prot diameter outlet diameter	mm	100 (4 ")
	Max.capa city traffic	m³h	96
	Cont.Head lift head	m	31
	Max.section head suction	m	8
Engine engine	Model: Engine model		HS-186FA
	Engine type Engine form		Single cylinder,4-stroke,air-cooled ，diesel engine Single cylinder, four stroke, air-cooled, diesel engine
	Bore x Stroke cylinder diameter x stroke		86*72
	Compression ratio		19:1
	Cubic cc.: Discharge consumption	cc	416
	Max.outpur(3600rpm) 功率	KW	9.2
	Alimentation: Fuel supply method		Natural self flowing type
	Cooling system: cooling method		Air cooled
	Starting system: Starting method		Recoil/Electric starter Hand Pull/Electric Start
	Rpm: Speed	rpm	3600
	Oil capacity: oil capacity	L	1.65
	Fuel tank capacity	L	5.5
	Fuel consumption ratio	g/kW.h	275.1
	Lube.brand lubricant model		CD grade or SAE10W-30, 15W-40 diesel engine oil
	Fuel type Fuel model		0 # in summer, -10 # in winter, diesel oil
Standard Features Standard Configuration	Connector of inlet and outlet pipe fittings		Yes, there is
	Filter Filter		Yes, there is
	Seal ring		Yes, there is
	Hoop clamp		Yes, there is
	Big fuel tank capacity		Optional
	Electric starter		Optional
Size Size	Packing size (L × W × H)	mm	650480610
	Net/Gross weight	kg	69/71
	20FT Qty		60
	40FT Qty		130

2 3 4 inch small diesel engine water pump

The automatic control operation process of the Hansi generator set is as follows:
1Keep the battery pack of the starter motor at the starting voltage.
2Keep the cooling water level of the radiator normal and keep the circulating water valve open.
3Maintain the crankcase oil level at the dipstick mark ±2cmWithin the scope.
4The fuel level in the fuel tank is more than half, and the fuel supply valve is normally open.
5Place the "Run Stop Auto" switch on the generator control panel in the "Auto" position.
6The mode switch of the generator set distribution panel is in the "automatic" position.
7Set the switch of the radiator fan to the "automatic" position.
8After receiving the signal of mains voltage loss, the unit starts up, confirms the mains voltage loss, cuts open the mains switch of the conversion cabinet, closes the power generation switch of the conversion cabinet, and starts the intake and exhaust fans in the machine room.
After my explanation, I hope it can be helpful to you. Hansi Care:
Precautions for editing this paragraph: The starter motor is used as a diesel generator setzuiOne of the important components, when using it, pay attention to the following points: 1After the preparation work is done, lift the start button, and the diesel engine gears will mesh with the flywheel ring gear and start running. Under normal circumstances, it can be started in one go. If the first start is unsuccessful, the starter armature must be stopped before proceeding to the next start. Otherwise, the starter gear will be severely impacted with the diesel engine ring gear and damaged.
2Each start-up time shall not exceed5The interval between second starts should be greater than2minute.
3When the engine fails to start several times in a row, the starter, diesel engine, battery, and wiring should be checked, and the fault should be eliminated before starting again.
4Once the diesel engine is started, the start button should be immediately released to allow the starter gear to return to its original position and stop working, in order to prevent damage to the starter due to overspeed.