German MAHR Pocket Surf ® IV roughness meter

NegotiableUpdate on 02/14

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Pocket sized, cost-effective, capable of measuring roughness on various surfaces, commonly used in production lines, workshops, and laboratories. Made of sturdy and wear-resistant cast aluminum, the surface measurement remains accurate and reliable even after years of use. Can measure any one of the four parameters in the series: Ra Rmax/Ry, Rz, and can choose to replace each other. After the measurement is completed, check all parameters. Within the range of 0.8mm/0.03in, you can choose a lateral displacement length of 1, 3, or 5 cut-off points.

Product Details

product description

A portable roughness meter that is pocket sized, cost-effective, and capable of measuring roughness on various surfaces. It is commonly used in production lines, workshops, and laboratories. There is no measuring instrument simpler than Pocket Surf, which can measure with just one button operation! Built in data output interface, economical and easy to replace battery.

German MAHR Pocket Surf ® Characteristics of the IV roughness meter:

Made firmly, the shell is made of wear-resistant cast aluminum, and even after years of use, the surface measurement is still accurate and reliable.
Can measure any one of the following four parameters: Ra, Rmax/Ry, Rz, and can choose to replace each other.
Check all parameters after the measurement is completed
Within the range of 0.8mm/0.3in, the lateral displacement length can be selected as 1, 3, or 5 cut-off points.
Measurements can be taken in horizontal, vertical, or inverted positions.
The probe has four switching positions - axial (overlapping with the X-axis), 90 °, 180 °, and 270 °.
Even surfaces that are difficult to reach, such as inner and outer diameters, can still be measured.
The integrated data output on the SPC processing device is compatible with most commonly used data processing systems.
Easy to recognize LCD reading display, for roughness measurements in micro inches or micrometers, it can be displayed half a second after crossing the surface horizontally.
When encountering situations such as "out of range" or "low voltage", a prompt will also appear on the screen.
The optimized digital calibration process eliminates scanning drivers and potentiometers, simplifying and accelerating the calibration process
Using standard 9V batteries, easy replacement, thus also improving battery life

MAHR Pocket Surf® IV粗糙度仪实拍图

Pocket Surf ® IV Technical Parameters:

Size	140x76x25mm//5.5'x3'x1'
Weight	435g /14Oz
Measurement range
Ra	0.03μm to 6.35μm /1μinch to 250μinch
Ry	0.2μm to 25.3μm /8μinch to 999μinch
Rmax	0.2μm to 25.3μm /8μinch to 999μinch
RZ	0.2μm to 25.3μm/8μinch to 999μinch
Display resolution	0.01μm/μin
Measurement accuracy	Meets ASME-B46.1, ISO, DIN standards, and MIL requirements
Digital display	The LCD also displays' Battery low '; Signal; 'H' and 'L' (measured values out of range)

MarConnect - USB Data Processing

Pocket Surf V uses the MarConnect interface. MarConnect simplifies the process of data transmission to PC, ensuring fast and universal assembly of multiple measurement stations.

		order No
Data cable USB (2m) including MarCom softwareStandard Edition	16EXU	4346023
Data cable Opto RS232C (2m), with SUB-D jack 9-pin	16 EXr	4346020
MarCom Software Professional Version 4.0 can connect 68 wired devices		4102550
MarCom Software Standard Version 3.1 can connect to 1 wired device		4102551

Pocket Surf ® IV probe selection:

Universal probe
EGH-1019/EGH-1026	Applied to most surface roughness
EGH-1026	Bring oneA 90 ° cone angle gemstone probe with a radius of 5 µ m/. 0002 "*.
EGH-1019	Bring a 90 ° cone angle gemstone probe with a radius of 10 µ m/. 0004 ".
Lateral probe
EGH-1020-W1	Used to measure the roughness of sharp edges or outer diameters, the probe is adjusted to 180 ° or aligned with the horizontal axis, with a 90 ° cone angle gemstone probe and a radius of 10 μ m/. 0004 ".
Parallel probe
EGH-1020-W2	Used to measure the roughness of sharp edges or outer diameters, the probe is adjusted to be perpendicular to the horizontal axis (90 ° or 270 °). It can also be used in situations where the outer diameter is less than 6.35mm./. 25 "as mentioned in EAS-2421, with a V-shaped fixture, a 90 ° cone angle gemstone probe, and a radius of 10 µ m./. 0004".
Small hole probe
EGH-1021/EGH-1027	Used for measuring small holes (inner diameter * 3.2 mm/. 125 ") * depth up to 19 mm/. 75".
EGH-1027	Equipped with a 90 ° cone angle gemstone probe with a radius of 5 µ m/. 0002 "*.
EGH-1021	Bring a 90 ° cone angle gemstone probe with a radius of 10 µ m/. 0004 ".
Deep probe for detecting the bottom of the groove
EGH-1028	Used to measure the bottom of grooves, dents, or small holes with a depth of 6.35mm/. 25 ". It is also used to measure short piston groove ridges and shaft shoulders. Bring a 90 ° cone angle gemstone probe with a radius of 10 µ m/. 0004 ".
Note: When using small hole probes and slot bottom probes for measurement, they must be at a 180 ° angle to the Pocket Surf supported by a height pedestal or other fixture. *The yellow dot at the end of the connecting pipe indicates a radius of 5 µ m/. 0002 ".

Learn more about Pocket Surf ® IV surface roughness meter price information, welcome to leave a message online or call for consultation!

Contact phone number: 021-58951071 QQ: 814294500